Professional heating, cooling & air quality services serving Beaverton and surrounding communities in Oregon. NATE-certified, 24/7 emergency response.
NATE-certified technicians providing the complete range of heating and cooling services.
Whether you are purchasing a home, preparing for seasonal demands, or evaluating replacement options, a thorough HVAC inspection provides actionable data. Technicians measure airflow, test safety controls, assess AFUE and SEER performance, and deliver a written report with prioritized recommendations.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
Restoring heat pump performance starts with accurate diagnostics of compressor function, reversing valve operation, and refrigerant charge levels. Our NATE-certified technicians service all major brands including Carrier, Trane, Lennox, and Rheem to resolve airflow loss, short cycling, and defrost failures.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
When your boiler produces inconsistent heat, unusual noises, or pressure fluctuations, the root cause often involves sediment buildup, failing motorized valves, or degraded seals within the hydronic loop. Experienced technicians restore system balance and verify safe operation through combustion analysis.
Sudden HVAC failures often stem from compressor lockout, blown transformer fuses, failed gas valves, or tripped high-pressure switches. Emergency repair service provides same-day response with technicians equipped to diagnose and resolve critical faults across all major heating and cooling equipment brands.
Properly sealed and insulated ductwork is essential for delivering rated BTU output to every room in your home. Our technicians repair collapsed sections, seal leaks with UL-listed mastic and mechanical fasteners, and verify balanced airflow across all supply registers after service.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
With 98,674 residents relying on dependable heating and cooling, Beaverton needs HVAC contractors who can deliver at scale without losing the personal touch. KIC Refrigeration has built our reputation in the Beaverton market by treating every project — from a thermostat installation to a full system replacement — with the same load calculation precision and installation quality.
Our Beaverton, OR teams know the HVAC landscape inside and out. We understand which neighborhoods have aging furnaces approaching end of life, where duct systems are undersized, and which equipment performs best across the Oregon climate. That local intelligence means better equipment recommendations and longer-lasting comfort for our customers.
What makes us different from every other heating and cooling company in the area.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Most service calls are completed the same day you call. Our trucks are stocked with over 200 common parts — capacitors, contactors, ignitors, flame sensors, motors, and control boards — so we resolve the majority of repairs in a single visit without waiting on parts.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Get the information you need to make confident HVAC decisions for your property.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Beaverton, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
Yes. KIC Refrigeration offers flexible financing options for HVAC installations in Beaverton, OR, including low-interest plans, deferred interest same-as-cash programs, and extended payment terms that make it easier to invest in high-efficiency equipment without a large upfront cost. Approved applicants can often finance a complete system replacement for less than $100 per month. We also help Beaverton homeowners identify and apply for available financial incentives including utility company rebates on high-efficiency equipment, manufacturer promotional pricing, and federal tax credits such as the 25C Residential Clean Energy Credit which provides up to $2,000 for qualifying heat pump installations and up to $600 for qualifying furnaces and air conditioners. Between financing, rebates, and tax credits, the effective cost of a new high-efficiency HVAC system is often significantly lower than the sticker price.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Beaverton including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Beaverton require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Oregon mechanical codes and International Mechanical Code standards.
As a guideline for Beaverton homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Oregon locations. For Beaverton homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"KIC Refrigeration handled our emergency furnace repair during a cold snap. They prioritized us because we have elderly parents in the home. Truly caring people."
"Boiler kept cycling on and off. Technician found a faulty thermocouple and replaced it on the spot. No nonsense, no upselling. Just good honest work."
"KIC Refrigeration installed our new heat pump system and the difference is incredible. Our energy bills dropped noticeably the very first month."
Professional heating and cooling services extending to neighboring cities and towns.